Last weekend we arrived at the Waikiki Yacht Club in Honolulu after a week-long cruise along the Kona Coast and the leeward shores of Maui and Molokai. We had a great trip–lots of exploring, diving and relaxing. But as good as that cruise was, the last week at the Waikiki Yacht Club was even better. The club is beautiful, with great people, and every day we walk to the shops and restaurants in Waikiki or along Ala Moana Blvd.
We landed in Hilo because it’s about 200 miles closer than Honolulu, and clearing into Hawaii would be simpler. Another advantage is that that we were windward of the other islands, so we could make a westerly run mostly downwind. The trip from Hilo also gave us an opportunity to use some equipment that we’d installed and tested, but had yet to really exercise. One of the most useful was the flopper-stopper (passive at-rest roll stabilizer). We’re not that sensitive to boat motion, so never had bothered with it until this trip. And we didn’t really notice the boat motion while anchored at Nishimura Bay (pictured above) where we first deployed it, until we tried to launch the tender. The dinghy swung dangerously when we got it in the air off the chocks, and we didn’t feel comfortable launching it with that much motion. The flopper-stopper made a huge difference.
The picture below shows the flopper-stopper in action. A line runs from the end of the pole up to the mast to hold the pole parallel to the water. Lines fore and aft keep the pole perpendicular to the boat. And a 4’x2′ folding metal plate is suspended from the end of the pole via a ring that connects by a short length of chain to each corner of the plate. As the boat rolls towards this side, the plate drops and folds. When the boat rolls back, the plate lifts and opens, resisting the boat motion like a parachute to reduce the return roll. The open plate is visible through the water. The small line coming in from the bottom left is a retrieval line. We initially attached the retrieval line to the ring with the suspension line, but found it twisted and tangled in the suspension line, preventing the plate from opening. Allowing the suspension line to spin freely about the retrieval line still allows us to retrieve the plate, but prevents the two lines from tangling.
We also used our Dayton Fan for the first time. We carry it to make working in the engine room more bearable in hot weather, but have been finding it useful in the cabin as well. On the crossing from San Francisco to Hawaii, the stateroom temperature reached the mid 80s–a little too hot for sleeping comfortably. We can open a small overhead hatch into the portuguese bridge (the walkway in front of the pilothouse windows), but it didn’t make much of a difference, and we couldn’t open it very wide in rough conditions. We could have started the generator and run the air-conditioning, but we’d rather not run the generator all the time. So we tried putting that big fan in the corner of the stateroom, and voila, instant cooling. It made a huge impact. The fan generates sufficient wind we use only the lowest setting. We also use the fan at anchor, both in the stateroom and in the pilothouse or salon. It is a little noisy, but underway with the engine running it’s not noticeable. And at anchor, the cooling is so welcome that we don’t mind the noise either.
Along with the rest of our canvas work, we asked Canvas Supply Company in Seattle make us window screens for all the pilothouse windows. These are made from a Sunbrella View tight weave material. They fit on the outside of the windows to provide sun heat and light protection, while still allowing some light in and a view out. (We didn’t have any made for the salon windows because we have translucent blinds for all those windows, mainly for privacy, but they do provide sun protection as well.) In Seattle, we’d not had much reason to use the windows screens. And we could have used them in San Francisco, but we were rather enjoying the sun. In the tropics, the screens really helped in reducing the temperature in the pilothouse, and improving comfort by not having the sun shine directly on us when we’re sitting up there.
We also had a few items that no longer were needed now that we were in the tropics. We switched our dive gear from cold-water to warm-water diving. We didn’t have to do a lot, mostly just get the neoprene booties and 3mm suits from storage, and stow the drysuits and cold-water gloves and hoods. We also removed the drysuit pressure hoses from our regulators. Wonder when we’ll put those back on again?
And we put all our sweaters, long-sleeved shirts, heavier coats and extra bedding into storage. We seal them in a Space Bags t to reduce the stored size and limit moisture intrusion. Space Bags are sealed plastic bags that you vacuum the air out of to reduce their size. The bags do slowly lose their vacuum over time, but it’s easy enough to re-vacuum them. And having them small to start with means we can stuff them into tight places.
Below is our log of the trip from Hilo to Honolulu. You also display these on the map view.
11/7/2012: Fuel fill
Hawaii Petroleum brought a truck over this morning and we took on 1,100 gallons of diesel.
|
11/7/2012: Farmers Market
Ron Rubin of N46-079 Alcyone told us about Hilo’s excellent farmers market.
|
11/7/2012: Outrigger
Around sunset, a dozen paddles launched this outrigger canoe and set off into Hilo Bay.
|
11/8/2012: Sinkers
Malasadas from the market. On past visits to Honolulu, we would pick up a load of delicious fresh-baked malasadas from Leonard’s Bakery en route to Hanauma Bay. We called them sinkers because we ate so many before we went snorkelling that we joked our heavy stomachs would sink us.
|
11/9/2012: Bike tour
We ran the bikes ashore in the dinghy for a tour of the Hilo area. The photo was taken on the Puueo St. bridge.
|
11/9/2012: Wailuku River
Looking down the Wailuku River, the 2nd longest in the state, from the Wainaku Ave bridge to Hilo Bay. In the distance is the Puueo St. bridge we were on earlier.
|
11/9/2012: Waterfall
Small waterfall on Wailuku River, looking west from from the Wainaku Ave bridge. About 3 miles upriver is 80′ Rainbow falls.
|
11/10/2012: Dawn
We left at 4:30am to pass around the south side of the island and begin a cruise up the Kona Coast.
|
11/11/2012: Beach house
Beach house to slightly to our south. The area was mainly pretty deserted the entire time we were there.
|
11/12/2012: Mauna Kea
The Mauna Kea observatories are just visible in the distance from the anchorage.
|
11/12/2012: Flopper-stopper
At anchor as the sun sets, with the flopper-stopper (passive at-rest roll stabilizer) deployed. We’ve never used it before other than in testing–we’re not that senstive to boat motion and didn’t really notice it until we tried to launch the tender. The dinghy swung dangerously when we got it in the air off the chocks, and we didn’t feel comfortable launching it with that much motion. The flopper-stopper made a huge difference.
|
11/13/2012: Alenuihaha Channel
We’re about halfway across Alenuihaha Channel, between the Big Island and Maui. The winds funnel and increase in strength here, and can generate hazardous conditions when strong tradewinds blow. The Mehaffy guidebook says the channel has a repution as being one of the worst in the world–a tugboat caption told the authors a wave here had torn the pilot house off his 60-foot steel tug. We were up at 3:30am to cross so winds would be lightest. So far we’re seeing the moderate conditions we deserve for the time we got up: seas mostly 6-8′. We’re getting a good push from the current as well, and are doing better than 8.5 knots.
|
11/13/2012: Lifeguard
Lifeguard tower on the beach. We could hear the lifeguard over a loudspeaker, warning beachgoers of the dangerous surf.
|
11/13/2012: Tourboat
This tour boat, packed with passengers, cruised slowly along the beach past our anchorage.
|
11/14/2012: Flopper-stopper in action
The flopper-stopper (passive at-rest roll stabilizer) in action. A line runs from the end of the pole up to the mast to hold the the pole parallel to the water. Lines fore and aft keep the pole perpendicular to the boat. And a 4’x2′ folding metal plate is suspended from the end of the pole via a ring that connects by a short length of chain to each corner of the plate. As the boat rolls towards this side, the plate drops and folds. When the boat rolls back, the plate lifts and opens, resisting the boat motion like a parachute to reduce the return roll. The open plate is visible through the water. The small line coming in from the bottom left is a retrieval line. We initially attached the retrieval line to the ring with the suspension line, but found it twisted and tangled in the suspension line, preventing the plate from opening.
|
11/16/2012: Heading to Molokai
We departed early this morning to cross Pailolo Channel between Maui and Molokai before the winds came up. Pailolo Channel isn’t considered as hazardous as Alenuihaha Channel between the Big Island and Maui, but conditions there still can be rough. The forecast today is for 30-knot winds and 14-foot seas.
|
11/16/2012: The Slot
We just passed through the junction of Pailolo, Auau, and Kalohi Channels, locally known as The Slot. The Coast Pilot reports that high winds and dangerous currents occur there. The wind has been blowing a steady 30 knots since we entered Pailolo Channel, and the waves have mostly been in the 6-8′ range on the beam. Passing through the Slot, however, we got hit with two 15′ waves in close succession. The first rolled us to the limit of the stabilizers and the second pushed us over 26.2 degrees.
|
11/16/2012: Kamalo Harbor
Lighted buoy off the entrance to Kamalo Harbor. Wave heights had settled, but the wind still blew at a steady 30 knots.
|
11/16/2012: Towards the entry
Heeled over in the wind as we look for the break in the reef to enter Kamalo Harbor. The least depth through the entry channel is only eleven feet.
|
11/17/2012: En route to Oahu
We were up just before 4am this morning to cross Kaiwi Channel, between Molokai and Oahu, before the afternoon winds picked up. The winds still were blowing from the east in the high 20s when we left Kamalo, but the forecast for Kaiwi looks reasonable: east winds 20 knots with 8-foot wind waves. Leaving the anchorage was a little challenging with the wind, darkness and tight quarters, but we took it slow and had no trouble. One advantage of the big winds is we’re getting a nice push through Kalohi Channel: we’re making over 9 knots.
|
11/17/2012: Penguin Bank
The winds have settled down as we cross Penguin Bank at the west end of Kalohi Channel, but we continue to make excellent time.
|
11/17/2012: Diamond Head in sight
We can see Diamond Head now–it’s only twenty miles away. We’ve lost a knot of speed, but still should arrive in Honolulu by early afternoon.
|
11/17/2012: Hanauma Bay
We’re directly south of Koko Head and Hanauma Bay now. The waves still are large, but are settling down a bit as we get into the lee of Oahu.
|
11/17/2012: Waikiki Yacht Club
Moored across from Starr, also of Seattle, at the Waikiki Yacht Club.
|
Hi James. I note your comment about where you attached the retrieval line on your flopper stopper. The pic shows the retrieval line connected to a ring that the flopper hanging down line passes through. Is that correct? I have the older style Forespar S/S flopper about one metre by one metre that I never used too often as it was rigged on the port side of our N5732 and too difficult to control. I have been running an Ocean Torque circular flopper that I launch and retrieve from the aft cockpit with the assistance of the davit. I have recently fitted a pole to the strbd side and intend to try the Forespar S/S folding flopper again. My plan was to launch and retrieve from the strbd side mid ships boarding gate. Launching will be simple. Retrieving is the challenge. I note the Magma folding floppers have the retrieval line attached near to the corner of the flopper itself. Your pic has the retrieval line connected to the flopper down line.? Any reason for that attachment point? Do you retrieve the flopper by hauling the retrieval line to the midships boarding gate? Can this be done manually by average strength or is Charles Atlas needed? Does the flopper tend to try to harpoon the hull? My flopper down line is rigged on a double block to allow the flopper to be raised/lowered hopefully with ease. My plan is to pull in the retrieval line and adjust the flopper down line as necessary to maintain control and hopefully avoid collision with the hull. This approach was not possible on the port side due to wide body saloon. I then plan a strop and hook attached to the
boom and connect the hook to the chain on the flopper when within reach. My flopper weights about 20 kgs. Do you think this approach will work??
Good eye Murray. You are right that the flopper recovery line is attached via ring to the down line rather than the designed location of being on the flopper itself. What we found was that when it was “properly” attached to the flopper, tangling was a frequent problem as the flopper rotated in current. Attaching it as we do eliminates the tangle problem but it’s slightly less effective to recover this way. I say slightly because it’s not really that different.
On our boat, we have a flopper only on the port side of an asymmetric house design so there is no walkway on that side. Consequently we launch from the swim platform by just lower the flopper in and then swinging the pull out by pushing the arm away from the hull while pulling in on fore guy. That’s very easy. To recover we release the fore guy slowly and swing it back to the rear of the boat. Then I go out to the swim platform and pull the recovery line until I can reach the down line. I pull it in nice and slow since, if you pull fast, it’s massively resistant. But, pulling slowly is easy. I just lift the flopper up onto the swim platform and carry it in. Pretty easy and it never tangles.